Last Updated Feb 2, 2011

PLEASE NOTICE NEW WEBSITE

LOCATION FOR ORDERING IS

http://r-charge.com

AND OWNERSHIP UNDER

RENAISSANCE CHARGE, LLC

NEW BATTERY SWAPPER BY BELOW.

 

 

Renaissance Charge Kit Credit Card Ordering Center.

We Accept Credit Cards With or Without Paypal, and over phone.

Radiant Energy Technology

We are also selling Battery Chargers at
Renaissance Charge LLC: r-charge.com

Exposing Mysticism and FE Hoaxs

Renaissance ChargeBattery Swapper

The Battery Swapper and Charger is a compact, but very complex device to move batteries in and out of a load environment for the purpose of charging each battery individually. With its LCD read out , terminal monitoring, logging capabilities and complex programming, this device can be used as a “Auto” or “Manual” Charger by selecting functionality presented on the LCD or Terminal display. Each section presented in this manual will explain the operational features of this device.

See new location of website for details: http://r-charge.com/kits.html

Click here for:

Books and DVDs

Feb. 2008 DVD
MONOPOLE MOTOR ENERGIZER PRESENTATION
An Overview and Demonstration of Basic Concepts, Building Instrctions, and Testing.
Improvement and complete refilming of the 2007 video put on Google Video.

See new location of website for details: http://r-charge.com/kits.html

Partial Parts Kit for SSG Motor Energizer

Most of the parts needed to build the Energizer

SSG Parts Kit SSG spool core and bifilar coils
Now comes with full circuit board, resistor jumper addition, and wire terminal.
SSG Circuit board
Includes a tiny bottle of drops of xcelplus lube And New Feb 2008 Presentation DVD mentioned above.

Order parts for what we are building on the list. Parts as shown in photos will be:
MJL21194 Transistor, 8 ceramic 8 magnets (3/8 by 1 7/8 by 7/8 ceramic grade 8 magnets) (for bigger wheels we recommend 12-24 magnets below), two diodes, one resistor, 1 potentiometer, one neon bulb, one small piece of aluminum with some transistor grease between it and the transistor, 2 coils of wire wound bifilar on a spool with the welding rods cut and fitted in the spool as the core.
For above parts excluding a rotor, frame, shaft, bearings, screws, batteries, battery wires, clips, glue and tape, click below:

See new location of website for details: http://r-charge.com/kits.html

Full SSG circuit board. Resistor jumper addition, and contact terminal with above kit only, or by special order. No parts but board included.

See new location of website for details: http://r-charge.com/kits.html

Large 10 Pole Monopole.

Large Bedini 10 Pole Monopole


Monopole replication of the large classic Energizer. This kit is made available because hundreds of people have asked for it over the years. We are providing a service to such people so that they can experiment with this technology and not have to spend tens of thousands of dollars having this system made up by machinists. It is not fully assembled and will not be assembled for people upon request. It is for learning and research purposes. Experiment at your own risk. Kit is molded and machined to the highest quality. This kit has 10 3" motor coils and a 17" aluminum rotor. 80 wires with 80 circuits on 10 circuit boards. It has an aluminum base frame with plexy glass top. You will be able to run the machine not only at 12V and 24V imputs, but over 100V. The larger the battery bank used the more you will get out of it (provided the batteries are in good condition). The system allows for the charging bank to be considerably higher voltage than the primary battery bank (or the same if desired). Also included is a generator coil that powers LEDs to light up the Bedini logo and clear plastic. Includes 80 SSG circuits, heat sink and pads, wire to batteries, clips, small sample of xcelplus. Comes with instruction CD and SSG DVD sold above. Customer assembles rotor, frame and circuit. It will consist of a rotor with magnets, and energizer coils with frame assembly. It will allow for back charging the primary battery bank or powering additional loads isolated from the 10 coiler (see below). The 10 coiler can be run with some of the motor coils replaced with one wire energizer coils for the same purposes. Or this system can be run as a 20 or 30 coiler for additional cost (see below). Shipped in five boxes.

      See new location of website for details: http://r-charge.com/kits.html

      10 Generator one wire coils added to the 10 coiler kit.

      10 Energizer coils 10 one wire coils (spools filled) with mounting molds, another rotor with magnets, and with frame assembly. Wire all 10 coils in series and you can put out AC or rectify it to DC with a bridge. Then you can add capacitors to store the charge and pulse it with the Tesla Solar Power Amplifier or other pulser into the front end or a load of your choice. This is NOT the same as a 20 coiler as shown below.

      See new location of website for details: http://r-charge.com/kits.html

      Additional 10 coils to make 20 or 30 coils on the same frame. Includes all additional parts to make 10 more coils and circuits with additional backing plate, for double the power and output.

      20 or 30 coiler

      See new location of website for details: http://r-charge.com/kits.html

      Classic 10 Pole Monopole Circuit board (for 8 SSG circuits).


      The circuit board has the potential for 8 SSG circuits with neon bulbs holes, diode holes, and several other features. The above kit comes with all circuit parts, including a switch that truns off the board through the trigger wire buss. That is, the trigger wire coming off the master coil (other side goes to negative) comes to the board at one hole. There is also another hole on the board for another wire to connect to go to the next board for multiboard systems like this ten coiler. This then can connect to a switch so that the board can turn off entirely (John's "sense" switch). This is nice on such a big system when you are wanting flexibility for experimentation. From there the buss is in series with a balance resistor, and from there the buss connects to each base resistor, either with a wire terminal block (as provided in the kit), or just directly to 8 resistors. The terminal block allows for easy swapping of resistors (as well as removal of coil) without having to unsolder the board. The board was made as small as possible given the parts used and heat sinking. The transistors are mounted upsidedown so that their backing faces away from the board onto an aluminum sink.

      Now Shipping.

4 Pole Monopole Jr.

4 Pole Monopole


This is a smaller version of the 10 coiler by frequent request. It just has a smaller and different rotor and less coils. Kits are molded and machined to the highest quality. This kit has four 3.5" motor coils (8 strands of #23 wire each) and a 6" by 1 7/8" aluminum rotor. 1/2" shaft at least 12" long. Also included is a generator coil that powers LEDs, which could also be used to do other work. May eventually include a commutator on the back to pulse the stored charge from a capacitor. Includes 32 SSG circuits, heat sink and pads, wire to batteries, spst switchs, small bottle of xcelplus. Comes with instruction CD and SSG DVD sold above. Shipping in 5 weeks.

      $1500 4 Pole Jr. Monopole (USA/Canada shipping included)

      $1600 4 Pole Jr. Monopole (International shipping included)

4 Pole Monopole Sr.

4 Pole Monopole


This is a smaller version of the 10 coiler by frequent request. It just has a smaller and different rotor and less coils. Kits are molded and machined to the highest quality. This kit has four 3.5" motor coils (8 strands of #18 wire each) and a 6" by 3" aluminum rotor. 7/8" shaft at least 12" long. Also included is a generator coil that powers LEDs, which could also be used to do other work. May eventually include a commutator on the back to pulse the stored charge from a capacitor. Includes 32 SSG circuits, heat sink and pads, wire to batteries, spst switchs, small bottle of xcelplus. Comes with instruction CD and SSG DVD sold above. Shipping in 5 weeks.

See new location of website for details: http://r-charge.com/kits.html

Large 12 Pole Monopole.

Large 12 Pole Monopole


Monopole replication of a large 12 Pole Energizer. This kit is made available because hundreds of people have asked for it over the years. We are providing a service to such people so that they can experiment with this technology and not have to spend tens of thousands of dollars having this system made up by machinists. It is not fully assembled and will not be assembled for people upon request. It is for learning and research purposes. Experiment at your own risk. Kit is molded and machined to the highest quality. This kit has 12 3.5" motor coils and a 6" x 12" aluminum rotor. 96 #18 gauge wires with 96 circuits on 12 circuit boards. It has an aluminum base frame with plexy glass top. You will be able to run the machine not only at 12V and 24V imputs, but higher. The larger the battery bank used the more you will get out of it (provided the batteries are in good condition). The system allows for the charging bank to be considerably higher voltage than the primary battery bank (or the same if desired). Also included is a generator coil that powers LEDs to light up the logo and clear plastic. Includes 96 SSG circuits, heat sink and pads, wire to batteries, clips, small sample of xcelplus. Comes with instruction CD and SSG DVD sold above. Customer assembles rotor, frame and circuit. Some of the coiles can be replaced with the single wire coils for additional generator function (for recharging the primary battery or powering other loads. Orders placed now ship approximately 6 weeks from payment. All orders shipped in five boxes.

See new location of website for details: http://r-charge.com/kits.html

Classic 3 Pole Monopole.

Classic 3 Pole Monopole

See new location of website for details: http://r-charge.com/kits.html

Classic Monopole replication of the Energizer. Kit is molded and machined to the highest quality. This kit has three 1.5" motor coils and a 3" aluminum rotor, with aluminum flywheel. Also included is a generator coil that powers 12 LEDs, which could also be used to do other work, like recharge the primary battery. May eventually include a commutator on the back to pulse the stored charge from a capacitor. Includes three SSG circuits, heat sink and pads, wire to batteries, clips, potentiometer, spst switch, bottle of xcelplus. Comes with instruction CD and SSG DVD sold above. Now Shipping.

See new location of website for details: http://r-charge.com/kits.html

      Attachment Gear for 1 to 15 persicion timing. Allows for transducing output to postive charge with an added capacitor. Also included tiny magnet, transistor, bridge and reed switch.

      Classic 3 Pole Monopole

    See new location of website for details: http://r-charge.com/kits.html

Advanced Monopole and Solid State Energizer.

Advanced Monopole and Solid State Energizer


This kit includes all of the above SSG kit (DVD also), and parts for an advanced inverted circuit on the back end, and parts for a solid state circuit. Instructions to be provided. A larger heat sink is provided than above kit. Includes 4' of wire (not all shown), a project box with wire terminals and grommet, and switches to switch between motor function and solid state function, and to switched between two different capacitor values for different kinds of charging purposes. Prototype picture shown is not exactly as parts look. A slightly larger project box and 3 different potentiometers are provided for easier mounting and adjustment. The solid state function does not need the wheel and magnets. The coil shown in the picture is three #23 wire, approx. 200' and 450 winds, twisted. This is the second option below. First option is for the above coil with two wires (#23, #26) in parallel not twisted, 900 winds.

See new location of website for details: http://r-charge.com/kits.html

      Kit with 900 winds of #23 and #26 wire:
      Kit with 200' of three #23 wires twisted:
      Advanced Kit without the SSG partial parts kit Coil, Magnets, Lube, DVD, and SSG circuit for those who have that already.

Window Motor Energizer Kit A


Window Motor Energizer Kit AThis 7" by 8" energizer is a carefully machined frame and rotor with 6 unique scalar manetic poles. The system uses the entire magnetic field of the super pole magnets for the greatest possible efficiency and energizer function. This toy size model is capable of running at 4 volts to possibly 48V or more, with 1 to 20 motor coils and circuits for a very large variation of power. The half inch solid brass shaft and carefully degreased bearings with xcelplus lube allows for very high rpm and strong motor function. The unique frame design allows for easy replacement of coils of different lengths and widths of wires, and easy mounting to holes or dowels. Design allows you to easily take it apart, and to mount it as you desire. We will make whatever custom size coil(s) you desire for this kit as shown on this webpage. The circuit provided is one full sequential bipolar circuit shown below. Also comes with two types of wire, terminal block, and two dpdt switches as shown in picture. The kit can be used to study motor or energizer function as well as serve as a platform for experiments for self-running capabilitities as outlined in the above Free Energy Generation book. A flywheel, commutator, or different types of loads can be attached to the rotor for additional experiments and benefits. System can be used to charge up one or more batteries of 2 to 200+ volts, or it can be run as a one battery system with the flip of a switch. S1 allows for two different motor speeds as well as center off position. Values of resistors and capacitor can also be substituted to personal preference. Coils can be left flat or bent around frame. Ships in box at just under 4 pounds.

See new location of website for details: http://r-charge.com/kits.html

Window Motor Energizer Kit B

Window Motor Energizer Kit B
Picture shown above only shows one of the three coils provided.

Rotor is 6" hexagon with 6" x 2" x 1" magnets. Comes with three motor coils and 3 bipolar sequential circuits, Hall triggering, heat sinks, wire, battery clips, etc. Coils will be formed for easy placement on motor. Requires easy assembly with instructions provided. Motor frame can hold more than 9 motor windings and can be run with high voltages to make for a lot of torque. Or it can be run slowly with very little imput (like 10ma @ 12V). Multistrand coils with additional circuitry can be ordered upon request. Weighs approximately 40 pounds. Shipping requires two boxes to reduce shipping costs.
      See new location of website for details: http://r-charge.com/kits.html

10 Spools used with Regular size Monopole Energizers.
3 3/4" H by 3.5" top and bottom, 3/4 bore.

10 Monopole Spools

See new location of website for details: http://r-charge.com/kits.html

5 Spools used with Monopole Energizers.

100 Spools used with SMALL size Monopole Energizers.
1.5" H x 1" W (top) 1.7" (base with holes), 1/4" bore. Strong plastic.

10 Small Monopole Spools

10 Small Spools used with SMALL Monopole Energizers.

      See new location of website for details: http://r-charge.com/kits.html

5 Small Spools used with SMALL Monopole Energizers.

      See new location of website for details: http://r-charge.com/kits.html

8 Ceramic Blocks 3/8 by 1 7/8 by 7/8 Grade 8 Magnets used with Monopole Energizers.

8 Monopole Magnets

See new location of website for details: http://r-charge.com/kits.html

R60 1/16" Welding Rods, (no spool) 6 oz, 3 1/4" long, makes 3/4" core.
Lincoln R60 Welding Rods

        See new location of website for details: http://r-charge.com/kits.html

TRANSISTORS

2N3440 NPN
2N3440 Transistor

MPS8599 PNP
MPS8599 Transistor

2N3440 NPN
2N3440 Transistor

See new location of website for details: http://r-charge.com/kits.htmlMJE3055 NPN
MJE3055 Transistor

MJE2955 PNP
MJE2955 Transistor

See new location of website for details: http://r-charge.com/kits.html

BD243C NPN
BD243C Transistor

MJ15024G NPN
MJ15024G Transistor

10 MJL21194 NPN Transistors used with Monopole Energizers.

10 Monopole Transistors

      See new location of website for details: http://r-charge.com/kits.html

      Or 5 MJL21194 Transistors used with Monopole Energizers.

      See new location of website for details: http://r-charge.com/kits.html

      10 MJL21193 PNP Transistors used with Monopole Energizers.

      10 Monopole Transistors

      See new location of website for details: http://r-charge.com/kits.html

          Or 5 MJL21193 Transistors used with Monopole Energizers.

          2N6509 SCR
          BD243C Transistor

          Hall Effect Sensor Switch
          HALL Transistor

          Reed Switch
          "Reed Switches 1 Form A 12mm AT 1015 OKI"
          REED Transistor

          555 Timer
          555 Transistor

          SG3524N For Tesla Switch and Full Capacitor Pulser
          SG3524N PWM Power Supply Controllers

          H11D1 Optocoupler HV Phototransistor For Capacitor Pulser
          SG3524N Optocouplers HV Phototransistor

          Bulbs

          0.026Amp Incandescent Wire Terminal Grain of Wheat Bulb

          Incandescent Wire Terminal Grain of Wheat Bulb

          See new location of website for details: http://r-charge.com/kits.html

          5 New Neon Ne-2 Bulbs Used with Monopole Energizers.

          5 Monopole Neon Bulbs

          See new location of website for details: http://r-charge.com/kits.html

          NOTE THAT TAPE MOTOR KIT IN DVD17 is the same as the Brushles Motor Fan Kits below:

          BRUSHLESS MOTOR FAN KITS
          Brushless Fan Energizer Kits

          8 to 52V 5 Inch Brushless Motor Fan Full Kit

          5 Inch Brushless Fan Energizer Kit

          This kit gives you all the parts needed to construct the above pictured brushless motor Energizer. Does not come with tools, glue, solder, wire connectors, or battery clips. Energizer conversion ran with supply voltages from 8V to 52VDC (voltages over 36V may require better heat sink for transistors). Fan is 24VDC rated for 27W.

          Contains two of all the SSG circuit parts of the partial kit above plus more. Does not include any potentiometer but does have 4 2W resistors (builder can swap these resistors with others supplied to change speed, or use other values). Larger diodes included. Added to this is the 27W brushless fan shown. Also as shown, one plastic display container, two 2PDT switches (so batteries can be rotated), the circuit and battery wire, one capacitor, one pulser circuit, and one tiny amount of xcelplus lube.

          See new location of website for details: http://r-charge.com/kits.html

          8 to 52V 6 Inch Brushless Motor Fan Full Kit

          Same kit as above but with large 6" fan.

          Brushless Fan SSG Parts Kit

          Very low res. 7MB video of the fan running before and after it was converted to an Energizer. Better quality video of this.

          Overview and conversion of the fan is shown in a video with WMV format that will be sent on a CD with the kit: This is the lower quality Google video. Other videos and pictures are included. This is a little higher quality.

          See new location of website for details: http://r-charge.com/kits.html

          10 Inch 8-52V Brushless Motor Fan Full Kit

          10 inch Brushless motor


          10 inch Brushless Energizer video. Same kit as above but with large 10" fan that is rated for 550CFMs (1.2A 24V). Energizer conversion ran with supply voltages from 8V to 52VDC (voltages over 24V require better heat sink for transistors).

          See new location of website for details: http://r-charge.com/kits.html

          We also have 10 uf 250V yellow capacitors for $1 each.
          10 uf 250V yellow capacitors
          Datasheet PDF
          See new location of website for details: http://r-charge.com/kits.html
          We also have 560 uF 400V capacitors for $5 each.
          See new location of website for details: http://r-charge.com/kits.html

          9 to 11 Pound Spools of Magnet Wire

          Essex Magnet Wire

          Shipping on second, fourth, sixth, etc., 10 pound spool is free for USA (as it fits in Priority F.R. Box), so click appropriate links below. Combine any two spools of wire. Substitutions of other thicker wire (#14 to #25) available upon request for same price, and thinner wire than #26 for slightly more cost. Magnet Wire is made and wound by Essex or other company and will vary from 9 to 11 pounds. Typical total weight is over 10 pounds, many are over 11 pounds. Spool is 6.4 oz.

          #23 Heavy insullation. (23 HVY GP/MR-200 CU6X3.5)

          See new location of website for details: http://r-charge.com/kits.html

          Custom Coils for Motors

          Custom Coils for Motors

          Coils all hand wound for quality control. Made of Magnet wire shown above. Let us know sales@r-charge.com what coil you want made for either the Window Motor or Monopole. Window coils not to be twisted, but monopole coils can be twisted as special order.

          Window Motor windings (100' lengths) for small kit including trigger wire(s):
          See new location of website for details: http://r-charge.com/kits.html
          Secondary windings (100') for second and third coils not needing triggers.
          See new location of website for details: http://r-charge.com/kits.html
          Window Motor windings (150' lengths) for small kit including trigger wire(s):
          See new location of website for details: http://r-charge.com/kits.html

          Secondary windings (150') for second and third coils not needing triggers.
          Monopole Coils on Spool with R60 Rod Cores:
          (free shipping on 2 or more coils under 20 pounds total)
          See new location of website for details: http://r-charge.com/kits.html
          The Rest of the Below Wire is Twisted before Winding:

          See new location of website for details: http://r-charge.com/kits.html

          Five Pound Coils (free shipping on 2nd, 3rd, and 4th under 20 pounds):
          8 Number 18 Wire 100 Foot long coils twisted
          150 Foot long coils twisted:

          3 #23 Wire 200 Foot (about 450 winds) long coils twisted:
          3 number 23 Wire 200 Foot about 450 winds long coils twisted

          See new location of website for details: http://r-charge.com/kits.html

          See new location of website for details: http://r-charge.com/kits.html

          8 #23 Wire 200 Foot long coils twisted:
          Energizer Coil, one wire #23 on 3.5" spool filled (approx. 5 pounds) with 1/16" R60 rods:
          Energizer Coil for Self-runner

          Order of 2nd, and 3rd is free shipping.

          20 Pound 8" diameter Coil 81 #23 Wires Twisted for Multistrand Monopole or Solid State circuits:
          6" high. Center of coil will be filled with welding R60 Welding Rods for a Core. Shipped in Flat Rate Priority box.
          81 Wire Coil for large multistrand setup

          Bipolar Circuit Replacement of SSG Circuit for first SSG Kit.

          Bipolar Circuit kit

          Contians ONE of each 1k 3/4W pot, MJE2955, MJE3055, MPSA06, 2A bridge, 1N914 Resistors: 100 ohms, 220 ohms, 2* 470 ohms. Does not include wire, magnet wire, coil, rotor, frame, glue, magnets, batteries, capacitor, Amperemeter, tape, heat sink, shaft, S1, or solder. May include tiny circuit board.

          Bipolar Circuit with Partial Motor Kit.

          Bipolar Circuit kit

          This contains the above Bipolar Circuit with the rest of the first SSG kit (magnets, coil, core rods, xcelplus lube, DVD).

          SMALL Sequential Bipolar Circuit for Magnetic Window Motor.

          Two Sequential Bipolar Circuit Kits

          Click above picture and see circuit on right side. This is the same as above (circuit only) but with double the parts except for the capacitor and bridge. Contians TWO of each 1k 3/4W pot, MJE2955, MJE3055, MPSA06, 1N914, Resistors: 100 ohms, 220 ohms, 4.7k (if you want the other resistor values instead, let me know); Four 470 ohms resistors, and one 2A bridge, and one 10uf 250V capacitor. Does not include wire, magnet wire, coil, rotor, frame, glue, magnets, batteries, Amperemeter, tape, heat sink, shaft, S1, or solder. Order one or in packs of five for discount.

          Or order packs of five for larger multistrand systems:

          See new location of website for details: http://r-charge.com/kits.html

          LARGE Sequential Bipolar Circuit for Magnetic Window Motor.

          Two Sequential Bipolar Circuit Kits

          Click above picture and see circuit on left side. May be used with 3 to 50V (if tranistors are kept under 150F) battery bank. This is the same as above but with larger transistors amd bridge Contians TWO of each 1k 3/4W pot, MJL21194, MJL21193, MPSA06, 1N914, Resistors: 100 ohms, 220 ohms, 4.7k, aluminum heatsinks (not as shown in picture), ; Four mica insulators, 470 ohms resistors, one 4A 1k bridge, and one 10uf 250V capacitor. Does not include wire, magnet wire, coil, rotor, frame, glue, magnets, batteries, Amperemeter, tape, shaft, S1, or solder. Order one or in packs of five for discount.

          See new location of website for details: http://r-charge.com/kits.html

          Or order packs of five for larger multistrand systems:


          See new location of website for details: http://r-charge.com/kits.html

          NEODYMIUM MAGNETS FOR MAGNETIC WINDOW MOTOR
          International orders need to contact us for shipping costs and details.

          Small Size Window Energizer using 2 inch magnets

          Six 0.5" x 0.5" x 1" Long Neodymium Iron Boron NdFeB Block Magnet Grade N42
          Magnetized through 1" length, poles are on the 0.5x0.5" ends
          Approximate pulling force: 55 lbs See new location of website for details: http://r-charge.com/kits.html
          Small Size Window Energizer using 2 inch magnets
          The above picture shows magnets that are actually half the size (1/2" x 1" x 2")

          Video of John 's motor in self-running mode using these magnets. Video of above pictured motor using half the magnet size.

          Six 1" x 1"x 2" Neodymium NdFeB Block Magnets, Ni-Cu-Ni Plated
          Grade N42, stronger than N40, N35, N38 Magnetized through the 2" Length (poles are on the 1x1" surfaces)
          Approximate pulling force: 207 lbs
          Gauss Rating: 13200

          See new location of website for details: http://r-charge.com/kits.html

          Medium Size Window Energizer using 4 inch magnets

          Six 4" x 1" x 1" Thick Rare Earth Neodymium NdFeB Block Magnets, Grade N42, Nickel-Copper-Nickel 3-Layer Coated
          BrMax: 13300 gauss
          BHMax: 42 MGOe
          Magnetized through the 1" Thickness
          Approximate pulling force: 205 lbs

          See new location of website for details: http://r-charge.com/kits.html

          4

          Six 4" x 2" x 2" Ni-Cu-Ni Plated Neodymium NdFeB Magnet Block N45
          25% stronger than N35
          Magnetized through the Thickness 2", poles are on the 4x2 surfaces
          pull force: 610 lbs

          See new location of website for details: http://r-charge.com/kits.html

          0-5A DC ANALOG WIDEVIEW PANEL METER.
          0-3A DC ANALOG WIDEVIEW PANEL METER

          See new location of website for details: http://r-charge.com/kits.html

          30A DC ANALOG WIDEVIEW PANEL METER.
          30A DC ANALOG WIDEVIEW PANEL METER

          See new location of website for details: http://r-charge.com/kits.html

          Choose below if you would like to donate to further this ministry. All help is appreciated. Or choose below numbers to add additional shipping amounts.

          Our name is:
          Renaissance Charge, LLC.

          Our Address is:
          10183 N. Aero Dr Ste 3.
          Hayden, ID
          83835
          Phone: (208) 772-4514
          potentialtec at yahoo . com
          Thank you.

          Copyright © 2006-2011 Renaissance Charge, LLC.